该设备为科研组合设备,包含相机组(固定资产编号:2023103001367)、LED点光源(固定资产编号:2023103001368)、位移台-针尖(固定资产编号:83599)、单轴位移台和控制器组合套件-针尖(固定资产编号:83598)、位移台-样品(固定资产编号:83600)、皮安表(固定资产编号:83606)。总体组合为一整套EGaIn观测机。主要用于进行调控微纳级别的间隙,然后进行测量的设备
VAP10/M 纵向位移台-针尖 的主要技术参数:
运动方向:垂直(Z轴)
负载能力:最大 10 kg
材质:高强度铝合金(表面阳极氧化处理)
行程范围:0 - 100 mm
分辨率:0.1 µm(取决于驱动器和控制系统)
重复定位精度:±1 µm
直线度:±2 µm/100 mm
平行度:±2 µm/100 mm
驱动类型:手动或电机驱动(可选)
手动驱动:精密微调旋钮
电机驱动:步进电机或伺服电机(需额外配置)
导向类型:精密交叉滚柱导轨
刚性:高刚性设计,适合高精度应用
摩擦力:低摩擦,确保平滑运动
台面尺寸:120 mm x 120 mm
整体尺寸:120 mm x 120 mm x 150 mm(高度)
重量:约 2.5 kg
CZF8-60 位移台-样品 的主要技术参数:
运动方向:垂直(Z轴)
负载能力:最大 10 kg
行程范围:0 - 300 mm
分辨率:0.01 mm(取决于控制系统)
重复定位精度:±0.02 mm
直线度:±0.05 mm/100 mm
平行度:±0.05 mm/100 mm
导向类型:精密滚珠丝杠
刚性:高刚性设计,适合高负载应用
摩擦力:低摩擦,确保平滑运动
台面尺寸:200 mm x 200 mm
整体尺寸:200 mm x 200 mm x 500 mm(高度)
重量:约 15 kg
KPZNFL5/M-NanoFlex™单轴位移台和控制器组合套件-针尖 的技术参数:
运动方向:单轴(X轴)或多轴(XY轴、XYZ轴可选)
负载能力:最大 5 kg
材质:高强度铝合金(表面阳极氧化处理)
行程范围:0 - 25 mm(单轴)
分辨率:0.1 nm(取决于驱动器和控制系统)
重复定位精度:±5 nm
直线度:±0.1 µm/25 mm
平行度:±0.1 µm/25 mm
驱动类型:压电陶瓷驱动器(Piezo Drive)
控制方式:闭环控制(集成传感器反馈)
控制接口:模拟电压输入(0-10 V)或数字接口(RS232/USB)
台面尺寸:100 mm x 100 mm(单轴)
整体尺寸:150 mm x 150 mm x 50 mm(单轴,高度)
重量:约 2 kg(单轴)
Keithley Model 6487 皮安表
1. 基本参数
型号:Keithley 6487
类型:皮安表(Picoammeter)
测量范围:电流测量范围从 2 nA 到 20 mA
分辨率:最低 10 fA(飞安)
2. 电流测量
测量范围:
2 nA 至 20 mA(共 8 个量程)
分辨率:
10 fA(在 2 nA 量程)
1 pA(在 20 nA 量程)
10 pA(在 200 nA 量程)
100 pA(在 2 µA 量程)
1 nA(在 20 µA 量程)
10 nA(在 200 µA 量程)
100 nA(在 2 mA 量程)
1 µA(在 20 mA 量程)
精度:
±(0.3% 读数 + 6 位最低有效数字)
3. 电压测量
电压源范围:0 至 500 V(可调)
电压测量范围:0 至 500 V
分辨率:1 mV
精度:±(0.1% 读数 + 0.02% 量程)
4. 输入特性
输入阻抗:> 10 TΩ(太欧)
输入电容:< 20 pF
输入偏置电流:< 3 fA(典型值)
5. 输出特性
电压源输出:0 至 500 V(可调)
电流源输出:0 至 20 mA(可调)
6. 通信接口
GPIB:支持 IEEE-488 标准
RS-232:支持串行通信
USB:支持 USB 接口(可选)
7. 环境适应性
工作温度:0°C 至 50°C
存储温度:-20°C 至 60°C
湿度:10% 至 90% RH(无凝结)
8. 电源要求
电源电压:100-240 V AC,50/60 Hz
功耗:最大 50 VA
9. 尺寸与重量
尺寸:89 mm x 213 mm x 350 mm(高 x 宽 x 深)
重量:约 4.5 kg
This equipment is a research combination device that contains a camera set (Fixed Asset No. 2023103001367), an LED point light source (Fixed Asset No. 2023103001368), a displacement stage - needle tip (Fixed Asset No. 83599), a single-axis displacement stage and controller combination kit - needle tip (Fixed Asset No. 83598), and a displacement stage - sample ( Fixed Asset Number: 83600),Pian meter (Fixed Asset No. 83606). The overall combination is a complete EGaIn observatory. Equipment primarily used to modulate gaps at the micro- and nano-levels and then measure them.
VAP10/M Longitudinal Displacement Stage - Needle Tip The main technical parameters of the VAP10/M Longitudinal Displacement Stage - Needle Tip:
Direction of motion: vertical (Z-axis)
Load capacity: max. 10 kg
Material: high-strength aluminum alloy (anodized surface)
Stroke range: 0 - 100 mm
Resolution: 0.1 µm (depending on drive and control system)
Repeatability: ±1 µm
Straightness: ±2 µm/100 mm
Parallelism: ±2 µm/100 mm
Drive type: manual or motorized (optional)
Manual drive: precision fine-tuning knob
Motor drive: stepper motor or servo motor (extra configuration required)
Guide type: Precision crossed roller guide
Rigidity: high rigidity design, suitable for high precision applications
Friction: Low friction to ensure smooth movement
Table size: 120 mm x 120 mm
Overall dimensions: 120 mm x 120 mm x 150 mm (height)
Weight: approx. 2.5 kg
Main technical parameters of the CZF8-60 displacement table - sample:
Direction of motion: Vertical (Z-axis)
Load capacity: max. 10 kg
Stroke range: 0 - 300 mm
Resolution: 0.01 mm (depending on control system)
Repeat positioning accuracy: ±0.02 mm
Straightness: ±0.05 mm/100 mm
Parallelism: ±0.05 mm/100 mm
Guide type: Precision ball screw
Rigidity: high rigidity design, suitable for high load applications
Friction: Low friction to ensure smooth movement
Table size: 200 mm x 200 mm
Overall dimensions: 200 mm x 200 mm x 500 mm (height)
Weight: approx. 15 kg
Technical data of the KPZNFL5/M-NanoFlex™ Single-Axis Displacement Table and Controller Combo Kit - Needlepoint:
Direction of motion: Single-axis (X-axis) or multi-axis (XY-axis, XYZ-axis optional)
Load capacity: 5 kg maximum
Material: high-strength aluminum alloy (surface anodized)
Travel range: 0 - 25 mm (single axis)
Resolution: 0.1 nm (depending on driver and control system)
Repeat positioning accuracy: ±5 nm
Straightness: ±0.1 µm/25 mm
Parallelism: ±0.1 µm/25 mm
Drive type: Piezo Drive
Control: Closed-loop control (integrated sensor feedback)
Control interface: analog voltage input (0-10 V) or digital interface (RS232/USB)
Table size: 100 mm x 100 mm (single axis)
Overall dimensions: 150 mm x 150 mm x 50 mm (single axis, height)
Weight: approx. 2 kg (single axis)
Keithley Model 6487 Picoammeter
1. Basic parameters
Model: Keithley 6487
Type: Picoammeter
Measuring range: Current measurement from 2 nA to 20 mA
Resolution: Minimum 10 fA (femtoamps)
2. Current measurement
Measuring range:
2 nA to 20 mA (8 ranges)
Resolution:
10 fA (in 2 nA range)
1 pA (in 20 nA range)
10 pA (in 200 nA range)
100 pA (at 2 µA range)
1 nA (in 20 µA range)
10 nA (at 200 µA range)
100 nA (at 2 mA range)
1 µA (at 20 mA range)
Accuracy:
± (0.3% of reading + 6 lowest significant digits)
3. Voltage Measurements
Voltage source range: 0 to 500 V (adjustable)
Voltage measurement range: 0 to 500 V
Resolution: 1 mV
Accuracy: ±(0.1% of reading + 0.02% of range)
4. Input Characteristics
Input impedance: > 10 TΩ (tera-ohm)
Input capacitance: < 20 pF
Input bias current: < 3 fA (typical)
5. Output Characteristics
Voltage source output: 0 to 500 V (adjustable)
Current source output: 0 to 20 mA (adjustable)
6. Communication Interface
GPIB: Supports IEEE-488 standard.
RS-232: Supports serial communication.
USB: Support USB interface (optional)
7. Environmental adaptability
Operating temperature: 0°C to 50°C
Storage temperature: -20°C to 60°C
Humidity: 10% to 90% RH (non-condensing)
8. Power requirements
Supply voltage: 100 to 240 V AC, 50/60 Hz
Power consumption: 50 VA maximum
9. Dimensions and Weight
Dimensions: 89 mm x 213 mm x 350 mm (H x W x D)
Weight: approx. 4.5 kg
该设备主要用于科研用途,其主要的功能是进行调控微纳级别的间隙,然后进行测量的设备。
This device is mainly used for research purposes and its main function is to carry out the regulation of the gap at the micro and nano level and then measure the device.
相机组(固定资产编号:2023103001367)、LED点光源(固定资产编号:2023103001368)、位移台-针尖(固定资产编号:83599)、单轴位移台和控制器组合套件-针尖(固定资产编号:83598)、位移台-样品(固定资产编号:83600)、皮安表(固定资产编号:83606)
Camera set (FTN: 2023103001367), LED point light source (FTN: 2023103001368), displacement table - needle tip (FTN: 83599), single axis displacement table and controller combo kit - needle tip (FTN: 83598), displacement table - sample (FTN: 83600)、Pian meter (Fixed Asset No. 83606)
公告名称 | 公告内容 | 发布日期 |
---|